24 Pin USB-C DIP SMT Connector Hybrid— USB-TC24-F09
The USB-TC24-F09 is a 24 pin usb-c dip smt connector that combines through-hole shell pins with surface-mount signal pads on one PCB footprint. The hybrid structure is the point of this model: the SMT pads handle the signal contacts during reflow, while the DIP shell legs pass through the board and are soldered separately, so the shell is anchored through the PCB as well as on its surface. Rated 5A / 30V DC, 20N max insertion, 5–20N withdrawal, and 10,000 mating cycles. Standard variant length is L=8.65mm; a longer L=10mm variant is available per drawing. For the standard-shell on-board DIP+SMT variant, see the USB-TC24-F02 DIP+SMT on-board receptacle.
24 Pin USB-C Hybrid Connector — What the DIP+SMT Structure Is For
A 24 pin usb-c hybrid connector exists because a pure SMT 24-pin receptacle carries insertion and withdrawal load only through its surface pads and shell anchor pads. In products where the port is exposed to frequent cable insertion, cable pull, or vibration, that load path can be a weak point. The hybrid structure adds through-hole shell legs that pass through the PCB and are soldered on the back side, so the shell is held by both the SMT joints and the through-hole joints. The signal contacts remain surface-mount; the shell anchoring is the through-hole part.
On this 24 pin usb-c dip smt connector, the contact set is the full-featured Type-C arrangement: four VBUS pins, four GND pins, two USB 2.0 lines, four SuperSpeed differential pairs, CC1/CC2, and SBU1/SBU2. That set is what allows the receptacle to support USB 3.1 SuperSpeed signaling, USB Power Delivery negotiation, and alternate modes such as DisplayPort Alt Mode, provided the host controller, device PHY, and cable support them. A 16-pin or 6-pin USB-C connector removes SuperSpeed lanes and cannot carry those signals regardless of the shell design.
This model is not a general-purpose 24-pin page and it is not a duplicate of the F02 or F04 pages. It is the hybrid variant, positioned around the DIP+SMT load path. If the assembly line is pure SMT and the port does not need through-hole shell anchoring, the USB-TC24-F04 SMT 24-pin receptacle is the simpler choice. If the design needs a mid-mount PCB cutout for a lower port height, the USB-TC24-F11 mid-mount serves a different footprint. The full set of variants is listed in the USB-C connector category.
DIP SMT USB-C Receptacle PCB — Technical Specifications for USB-TC24-F09
| Parameter | Specification | Notes |
|---|---|---|
| Part Number | USB-TC24-F09 | Hybrid DIP+SMT variant |
| Connector Type | USB Type-C Female Receptacle | 24-pin full-featured |
| Pin Count | 24 Pins | A-side / B-side dual row |
| Interface Standard | USB 3.1 Type-C | USB 2.0 backward compatible |
| Mounting Type | DIP + SMT (Hybrid) | SMT signal pads + through-hole shell legs |
| Orientation | Horizontal | Port exits parallel to PCB |
| Length L (Standard) | 8.65 mm | Standard variant |
| Length L (Optional) | 10 mm | Per drawing; confirm before PCB keep-out |
| Current Rating | 5A | Connector-level VBUS/GND rating |
| Voltage Rating | 30V DC | Connector-level rating |
| Insertion Force | 20N Max | — |
| Withdrawal Force | 5–20N | Retention range |
| Durability | 10,000 Cycles | Mating / unmating |
| Compliance | RoHS / REACH | — |
| Packaging | Reel / Tray | Production handling options |
The two L values are separate variants of the same hybrid footprint family, not two numbers for one part. Confirm which L applies to your order and drawing before releasing the PCB keep-out. As a dip smt usb-c receptacle pcb layout, the footprint must include both the SMT land pattern and the through-hole shell-leg pattern; the drawing is the only source for the exact pad and hole coordinates. When selecting a 24 pin usb-c dip smt connector, treat the 5A / 30V DC figure as a connector-level rating: actual product power depends on the PD controller, power supply, cable, thermal path, and protection circuit. The 24-pin contact set and the hybrid shell structure are independent of the negotiated data rate, which is set by the host, device, and cable. For the official USB 3.1, USB Power Delivery, and Type-C interface rules, the USB-IF USB Power Delivery page and the USB-IF USB Type-C specification page document the power negotiation and interface dimensions behind the connector rating.
Hybrid Mount USB-C Receptacle — Key Design Features for High-Insertion PCBs
DIP+SMT Hybrid Load Path
The signal contacts are SMT pads reflowed with the top-side components. The shell legs are through-hole pins that pass through drilled holes in the PCB and are soldered on the back side. When a cable is inserted or pulled, part of the force transfers into the through-hole shell legs instead of relying only on the SMT shell anchor joints.
Full 24-Pin Contact Set
The full-featured Type-C arrangement carries VBUS, GND, D+/D−, SuperSpeed TX/RX pairs, CC1/CC2, and SBU1/SBU2. This is the contact set that a 16-pin or 6-pin USB-C receptacle does not have, and it is what allows the connector to support USB 3.1 SuperSpeed signaling and alternate modes when the host, device, and cable support them.
5A / 30V DC Connector Rating
The VBUS/GND contacts are rated for 5A at 30V DC at the connector level. This is the connector ceiling, not the delivered wattage of a finished product. The actual USB PD power depends on the PD controller, power supply, cable, thermal path, and protection circuit on the same board.
10,000 Mating Cycles
Rated for 10,000 insertion and withdrawal cycles at the connector level, with 20N max insertion force and 5–20N withdrawal force. Product-level cycle life still depends on enclosure alignment, cable handling, and how the panel supports the mated plug during use.
Two Shell Length Variants
The standard variant is L=8.65mm. A longer L=10mm variant is available per drawing. These are two length variants of the same hybrid footprint family, not one part with two numbers. Confirm which length applies to your order and PCB keep-out before release.
Assembly Process Compatibility
The signal pads reflow with the top-side SMT components. The shell legs need a through-hole soldering step, either selective soldering or wave soldering depending on the line. The connector body must be able to pass through that stage without damage; confirm the process with the board house before releasing the build.
24 Pin USB-C DIP SMT Receptacle for High Insertion — Where the Hybrid Shell Matters
A 24 pin usb-c dip smt receptacle for high insertion use is the reason this model exists next to the pure SMT version. The hybrid shell is most relevant when the port is a user-facing interface that sees repeated plug and unplug events, when the cable may be pulled at an angle, or when the product is installed in an environment with vibration. In those cases, the through-hole shell legs give the connector a second anchoring path that does not rely solely on the SMT joints.
The hybrid shell does not replace enclosure support. The enclosure still needs to align the port opening with the connector body and take load off the PCB where possible. The hybrid structure adds through-hole anchoring; it does not remove the need for a mechanically sound panel design. Products that combine a well-supported enclosure with a 24 pin usb-c dip smt connector are the intended use case. For products where the port is not user-facing or where the cable is connected once during installation, a pure SMT receptacle is often sufficient and simpler to assemble.
24 Pin USB-C Pinout — Signal Groups Inside the Receptacle
The 24 pin usb-c dip smt connector follows the standard 24-pin Type-C contact arrangement, which uses a symmetrical dual-row layout so the plug works in either orientation. The table below groups the 24 contacts by function rather than listing individual pin numbers, because the A-side and B-side rows mirror each other and the pin numbers should be read from the current drawing for PCB layout.
| Function Group | Role | Notes |
|---|---|---|
| VBUS (×4) | Power delivery | Connector rated 5A at VBUS/GND |
| GND (×4) | Ground return | Paired with VBUS for current path |
| D+ / D− (×2 pairs) | USB 2.0 data | Mirrored on A and B sides |
| SSTX1/2, SSRX1/2 (×4 pairs) | SuperSpeed differential | USB 3.1 signaling; dual-lane capable |
| CC1 / CC2 | Configuration channel | Orientation detection and PD negotiation |
| SBU1 / SBU2 | Sideband use | Alternate mode, e.g. DisplayPort Alt Mode |
The exact pin numbering for the A-side and B-side rows should be taken from the current drawing before PCB layout. The grouping above is the functional map that the 24-pin contact set follows. For a full pin-by-pin table across USB-C receptacle types, the USB-C connector pinout guide includes the 24-pin front-view assignment and a comparison with 16-pin and 6-pin variants. The pin map does not change between the hybrid and pure SMT versions of the 24 pin usb-c dip smt connector; the mounting structure is separate from the contact assignment.
F09 vs Other 24-Pin USB-C Receptacles — Selection Guide
The 24-pin lineup has several variants that share the same contact set but differ in mounting, shell, and assembly process. The table below is a selection guide, not a ranking. Each row points to a different page because the requirement is different.
| Requirement | Start With | Why |
|---|---|---|
| Hybrid DIP+SMT shell anchoring for high-insertion or vibration-prone designs | USB-TC24-F09 (this page) | Through-hole shell legs + SMT signal pads; L=8.65mm standard, L=10mm optional |
| Standard-shell DIP+SMT on-board, horizontal | USB-TC24-F02 | DIP+SMT on-board, no extended-shell positioning |
| Pure SMT reflow, no through-hole step | USB-TC24-F04 | SMT-only 24-pin; simpler assembly flow |
| Single-row SMT, USB4 40Gbps positioning | USB-TC24-F30 | Single-row right-angle SMT; different footprint |
| Mid-mount PCB cutout, lower port height | USB-TC24-F11 | Mid-mount, 10Gbps positioning |
Among 24 pin usb-c dip smt connector options, the hybrid shell does not make this model the “best” one in a general sense. It makes it the right starting point when the mechanical requirement calls for through-hole shell anchoring. For products where the port is not exposed to repeated cable load, a pure SMT or standard DIP+SMT receptacle is often a better fit for assembly simplicity. The full 24-pin lineup and its mounting options are maintained in the USB-C connector category.
FAQ — USB-TC24-F09 Hybrid DIP+SMT Receptacle
Is the F09 the same as the F02 DIP+SMT on-board receptacle?
No. Both are 24 pin usb-c dip smt connector variants, but they are different pages and different parts. The F09 is the hybrid-shell positioning with L=8.65mm standard and L=10mm optional; the F02 is the standard-shell on-board DIP+SMT variant. Compare the drawings before choosing, and do not copy L values between the two models.
Are L=8.65mm and L=10mm the same model?
They are two length variants within the hybrid footprint family, not one part with two numbers. The standard variant is L=8.65mm; the L=10mm variant is available per drawing. Confirm which length applies to your order and PCB keep-out before release.
What does the hybrid DIP+SMT structure actually anchor?
It anchors the shell. The signal contacts are SMT pads reflowed with the top-side components. The shell legs are through-hole pins that pass through the PCB and are soldered on the back side. This gives the shell a second load path through the board, in addition to the SMT shell anchor pads and the enclosure support.
Does the 5A rating mean the product supports 240W USB PD?
No. The 5A rating is the connector’s VBUS/GND rating. Actual USB PD power depends on the PD controller, power supply, cable, thermal design, and protection circuit. The connector is one element of a high-power design, not a guarantee of delivered wattage.
Does the hybrid shell change the data rate or the pinout?
No. The 24-pin contact set and its functional pin groups are the same as a pure SMT 24-pin receptacle. The hybrid structure changes how the shell is anchored, not what the contacts can carry. Data rate is set by the host, device, and cable, not by the shell mounting.
Can the F09 be used on a pure SMT line?
For a 24 pin usb-c dip smt connector, the signal contacts are SMT, but the shell legs require a through-hole soldering step. If the line is pure SMT and cannot handle that step, the F04 pure SMT page is the simpler comparison. If the line already has a through-hole stage for other components, the F09 uses that stage for the shell legs.
16 Pin USB-C Connector Mid-Mount SMT – 10Gbps USB 3.2 Receptacle

USB Type C SMD Connector 6 Pin Female Receptacle
24 Pin Vertical USB-C Connector SMT, H=13mm (USB-TC24-F17)

USB Motherboard Connector C 16P SMT Right Angle USB 3.1 Female Receptacle
Mid Mount USB C Connector — 24 Pin Double Shell, L=8.65mm, CL=0.32mm for Ultra-Thin PCBs
24 Pin USB-C Female Connector SMT Vertical — USB-TC24-F15, H=9.25/10.45mm, 5A/20V
USB Type-C Female Connector 6 Pin Mid-Mount – Durable 3A Power Delivery for Space‑Limited PCBs
USB Type-C Connector 24 Pin Flank SMT (USB-TC24-F28M02)
USB-C Connector Pinout Guide for Engineers: 24-Pin vs 16-Pin Signal Assignment & PCB Routing
When moving from the pinout to a physical part, orientation matters as much as pin count. The USB-TC24-F12 (vertical SMT solder mount)...
USB-C 24-Pin Full-Featured vs. 16-Pin USB 2.0: Key PCB Layout Considerations
Understanding the differences in PCB layout between the USB-C 24-pin full-featured and 16-pin USB 2.0 connectors is crucial for ensuring stable device...

USB-C vs USB 3.0 vs USB4: Which Connector Do You Need for Your Next Design?
If you’re specifying a USB connector for a new product, you’ve probably run into three overlapping terms: USB-C, USB 3.0, and USB4....