24 Pin USB Type-C Female Connector Mid-Mount — Single Shell, L=8.65mm, CL=0.32mm for Ultra-Thin PCBs

The USB-TC24-F10 is a 24pin usb type-c female connector mid-mount built around a single-shell body, L=8.65mm length, and CL=0.32mm board offset. It is a 24-pin full-featured receptacle, rated 5A / 30V DC, 10,000 mating cycles, and −40°C to +85°C, with SMT mounting and a mid-mount footprint that recesses the connector body partly into a PCB cutout. This page treats F10 as the single-shell mid-mount variant. For the dual-shell mid-mount comparison, see the USB-TC24-F11 mid-mount page.

Part NumberUSB-TC24-F10
Connector TypeUSB Type-C Female Receptacle
Pin Count24 Pins
Mounting TypeSMT, Mid-Mount
ShellSingle Shell

24Pin USB Type-C Female Connector Single Shell — What Mid-Mount Changes on the PCB

A 24 pin usb-c female connector single shell mid-mount part is not simply a top-mount receptacle lowered by a few tenths of a millimeter. The connector body sits partly inside a slot milled into the PCB, so the mating opening is closer to the board surface. On the F10, that recess is defined by CL=0.32mm, and the body length is L=8.65mm. The result is a lower above-board profile than a standard top-mount 24-pin SMT receptacle, which matters when the enclosure is thin and the port is close to the PCB.

The single-shell structure is the second distinguishing point. The F10 uses one shell body, while the F11 is the dual-shell mid-mount variant. The shell count is not a cosmetic difference: it affects the connector envelope, the mating engagement, and the way the port fits the enclosure cutout. The F10 page is written around the single-shell envelope and the L=8.65mm / CL=0.32mm footprint. If the design needs the dual-shell envelope, the F11 page is the correct starting point.

On the electrical side, the F10 keeps the full 24-pin contact set: four VBUS pins, four GND pins, D+/D−, SuperSpeed TX/RX pairs, CC1/CC2, and SBU1/SBU2. That set is what separates a full-featured 24-pin receptacle from a 16-pin or 6-pin USB-C port. The mid-mount shell and the single-shell body change the mechanical envelope, not the contact assignment. Data rate and power delivery still depend on the host controller, device PHY, cable, and PD circuit.

The F10 sits in the USB-C receptacle product family alongside top-mount SMT, DIP+SMT hybrid, single-row SMT, and waterproof mid-mount models. It is not a replacement for those pages. It is the single-shell mid-mount 24-pin option for designs where board height is the limiting factor and the enclosure needs the port recessed into the PCB.

Technical Specifications

Mid-Mount USB-C Receptacle PCB — Technical Specifications for USB-TC24-F10

ParameterSpecificationNotes
Part NumberUSB-TC24-F10Single-shell mid-mount variant
Connector TypeUSB Type-C Female Receptacle24-pin full-featured
Pin Count24 PinsA-side / B-side dual row
Mounting TypeSMT, Mid-MountBody partly recessed into PCB cutout
ShellSingle ShellF11 is the dual-shell mid-mount variant
Length L8.65 mmBody length
CL (Board Offset)0.32 mmMid-mount recess depth
Current Rating5A MaxConnector-level VBUS/GND rating
Voltage Rating30V DCConnector-level rating
Durability10,000 Mating CyclesInsertion / withdrawal
Operating Temperature−40°C to +85°C—
Contact MaterialCopper Alloy—
Contact PlatingGold Plated—
Housing MaterialHigh Temperature ThermoplasticLead-free reflow compatible
ComplianceRoHS / REACH—
PackagingReel / TrayProduction handling options

The L and CL values are the two dimensions that separate a mid-mount layout from a top-mount layout. L=8.65mm defines the body length; CL=0.32mm defines how far the connector sits into the board. Both must be taken from the current F10 drawing before the PCB cutout and keep-out are released. The 5A / 30V DC figure is a connector-level rating, not the delivered power of a finished product. USB PD wattage still depends on the PD controller, power supply, cable, thermal path, and protection circuit. For the official Type-C interface rules behind the 24-pin contact set, the USB-IF USB Type-C specification page documents the interface dimensions and pin functions.

Key Features

24 Pin USB-C Mid-Mount Connector L=8.65mm — Key Design Features

📐

Mid-Mount with CL=0.32mm Recess

The connector body sits partly in a PCB cutout, with CL=0.32mm defining the recess depth. This lowers the above-board profile compared with a standard top-mount 24-pin SMT receptacle, which matters in thin enclosures where the port height is constrained.

🔩

Single-Shell Envelope, L=8.65mm Body

The F10 uses a single shell body with L=8.65mm length. The F11 is the dual-shell mid-mount variant. Shell count affects the connector envelope and the way the port fits the enclosure cutout; the two should be compared on the drawing, not treated as interchangeable.

⚡

Full 24-Pin Contact Set

The receptacle carries VBUS, GND, D+/D−, SuperSpeed TX/RX pairs, CC1/CC2, and SBU1/SBU2. This is the contact set that a 16-pin or 6-pin USB-C port does not have, and it is what allows the connector to support USB 3.1 SuperSpeed signaling and alternate modes when the host, device, and cable support them.

🔋

5A / 30V DC Connector Rating

The VBUS/GND contacts are rated for 5A at 30V DC at the connector level. This is the connector ceiling, not the delivered wattage of a finished product. The actual USB PD power depends on the PD controller, power supply, cable, thermal path, and protection circuit on the same board.

💪

10,000 Mating Cycles

Rated for 10,000 insertion and withdrawal cycles at the connector level. Product-level cycle life still depends on enclosure alignment, cable handling, and how the panel supports the mated plug. The mid-mount recess and the shell body both affect that mechanical interface.

🏭

SMT Reflow, Mid-Mount Cutout

The connector is SMT-mounted, so the signal pads and shell anchor pads are reflowed with the top-side components. The mid-mount footprint adds a PCB cutout requirement. The board house should confirm the cutout dimensions against the F10 drawing before the board is released.

USB-C Female Connector CL=0.32mm — Where Mid-Mount Fits Best

A usb-c female connector cl=0.32mm recess is useful when the product enclosure is thin and the USB-C port cannot sit fully above the PCB. The mid-mount structure lets the connector body drop into a board cutout, so the mating opening lines up with a lower panel opening. This is the same logic that drives mid-mount use across ultra-thin devices, but the F10 is specifically the single-shell, L=8.65mm variant. The dual-shell F11 page serves a different envelope.

📱 Ultra-thin consumer devices Products where the PCB-to-panel distance is tight and the USB-C port must sit close to the board surface without a tall above-board profile.
💻 Compact computing and tablets Mainboards where the USB-C port is placed near the edge of a thin enclosure and the mid-mount cutout helps align the port with the panel opening.
🔌 Docking hardware and hubs Port expanders and docking boards where multiple USB-C ports are placed close together and a lower profile helps with enclosure stacking.
🏭 Industrial HMI and control panels Panel-mounted control hardware where the board sits behind a front panel and the mid-mount recess reduces the gap between the port and the panel cutout.
📡 IoT gateways and edge devices Compact networking hardware where the enclosure is shallow and the USB-C port is a service or data interface.
🎧 Audio/video and portable equipment Products where the USB-C port is on the main PCB and the mechanical height budget rules out a standard top-mount receptacle.

Mid-mount is not a universal upgrade. It adds a PCB cutout requirement and changes the mechanical load path compared with a top-mount receptacle. If the enclosure is not height-constrained, a top-mount or DIP+SMT receptacle is often simpler to assemble. The F10 is intended for designs where the mid-mount recess solves an actual mechanical constraint, not as a default choice across every 24-pin project.

24 Pin USB-C Pinout — Signal Groups Inside the Mid-Mount Receptacle

The 24-pin Type-C interface uses a symmetrical dual-row layout so the plug works in either orientation. The mid-mount shell and single-shell body do not change the contact map; they change the mechanical envelope. The table below groups the 24 contacts by function.

Function GroupRoleNotes
VBUS (×4)Power deliveryConnector rated 5A at VBUS/GND
GND (×4)Ground returnPaired with VBUS for current path
D+ / D− (×2 pairs)USB 2.0 dataMirrored on A and B sides
SSTX1/2, SSRX1/2 (×4 pairs)SuperSpeed differentialUSB 3.1 signaling; dual-lane capable
CC1 / CC2Configuration channelOrientation detection and PD negotiation
SBU1 / SBU2Sideband useAlternate mode, e.g. DisplayPort Alt Mode

The exact pin numbering for the A-side and B-side rows should be taken from the current drawing before PCB layout. For a full pin-by-pin table across USB-C receptacle types, the USB-C connector pinout guide includes the 24-pin front-view assignment and a comparison with 16-pin and 6-pin variants. The pin map is the same for the F10 single-shell mid-mount and the F11 dual-shell mid-mount; the mounting and shell structure sit outside the contact assignment.

F10 vs F11 and Other 24-Pin USB-C Receptacles — Selection Guide

The 24-pin lineup has several variants that share the same contact set but differ in mounting, shell, and assembly process. The table below is a selection guide, not a ranking. The F10 and F11 are both mid-mount 24-pin receptacles, but they are not the same connector: F10 is the single-shell variant, F11 is the dual-shell variant. The L and CL values should be compared on the drawings before either part is designed in.

RequirementStart WithWhy
Single-shell mid-mount, L=8.65mm, CL=0.32mmUSB-TC24-F10 (this page)Single-shell body; mid-mount recess for thin enclosures
Dual-shell mid-mount 24-pinUSB-TC24-F11Dual-shell envelope; compare drawing and CL before selection
Standard top-mount SMT, no PCB cutoutUSB-TC24-F04Pure SMT top-mount; simpler assembly, taller above-board profile
DIP+SMT hybrid shell anchoringUSB-TC24-F09Through-hole shell legs for high-insertion or vibration-prone designs
Single-row SMT, USB4 40Gbps positioningUSB-TC24-F30Single-row right-angle SMT; different footprint and speed positioning
Waterproof IP67/IP68 mid-mountUSB-TC24-FW10Sealed mid-mount for outdoor or wet environments

Among 24pin usb type-c female connector mid-mount options, the F10 should be selected on the shell and the L/CL dimensions, not on the pin count alone. The 24-pin contact set is shared across these variants. If the design does not actually need a mid-mount cutout, a top-mount SMT or DIP+SMT receptacle is often easier to assemble. If the design does need a mid-mount but the shell envelope is different, the F11 or another mid-mount variant in the USB-C receptacle category should be compared before the PCB cutout is finalized.

FAQ

FAQ — USB-TC24-F10 Single-Shell Mid-Mount Receptacle

Is the F10 the same as the F11 mid-mount receptacle?

No. Both are mid-mount 24-pin receptacles, but the F10 is the single-shell variant with L=8.65mm and CL=0.32mm, while the F11 is the dual-shell mid-mount variant. The shell count and the resulting connector envelope are different. Compare the drawings before choosing, and do not assume the L or CL values are interchangeable.

What do L=8.65mm and CL=0.32mm mean on this connector?

L=8.65mm is the connector body length. CL=0.32mm is the board offset that defines how far the mid-mount body sits into the PCB cutout. Both are mechanical dimensions that should be taken from the current F10 drawing before the board keep-out is released.

Does mid-mount change the pinout or the data rate?

No. The 24-pin contact set and its functional pin groups are the same as a top-mount 24-pin receptacle. The mid-mount structure changes the mechanical height and the PCB cutout requirement, not the contact assignment or the negotiated data rate. Data rate is set by the host, device, and cable.

Does the 5A rating mean the product supports 240W USB PD?

No. The 5A rating is the connector’s VBUS/GND rating. Actual USB PD power depends on the PD controller, power supply, cable, thermal design, and protection circuit. A 5A connector can be part of a high-power design, but the delivered wattage is set by the full system.

What PCB change is required for a mid-mount connector?

A mid-mount connector requires a slot or cutout in the PCB so the connector body can sit partly below the board surface. The cutout dimensions, the SMT land pattern, and the connector body keep-out should all be checked against the F10 drawing. If the board cannot accommodate a cutout, a top-mount SMT receptacle is the simpler alternative.

Is the F10 available in a dual-shell version?

The F10 is the single-shell mid-mount variant. The dual-shell mid-mount 24-pin option is covered on the USB-TC24-F11 page. Shell count affects the connector envelope and the enclosure fit, so the two should be compared on the drawing before selection.

Request a Quote

    Inquiry for:

    Loading product...