Vertical Slide Switch DIP 8 Pin — SS-23L10 Through-Hole 8-Pin Vertical Slide Switch for Audio, Instrumentation & Industrial Controls

The SS-23L10 vertical slide switch is a compact, top‑actuated vertical slide switch in a standard 8‑pin DIP footprint. Unlike horizontal slide switches that move parallel to the board, this vertical slide switch DIP 8pin features a slider that travels perpendicular to the PCB, making it ideal for edge‑mounted control panels, vertically oriented daughterboards, and space‑constrained front‑panel applications. The 2‑pole 3‑throw configuration allows simultaneous switching of two independent signal paths among three positions — perfect for audio input selection, gain setting, or mode toggling on test equipment.

The through‑hole DIP mounting ensures robust mechanical anchoring, resisting the lateral forces generated during repeated actuation. Each of the eight gold‑plated phosphor bronze terminals provides stable, low‑resistance contact, while the high‑temperature PBT housing withstands wave‑solder temperatures. With a positive detent mechanism providing clear tactile and audible feedback at each position, the SS-23L10 eliminates ambiguous intermediate states and enhances user confidence. From professional audio mixers and studio outboard gear to industrial PLC configuration modules, this slide switch delivers reliable, long‑term performance.

Recommended Footprint

The SS-23L10 uses a standard 8‑pin DIP footprint with 2.54mm (0.1″) pitch and 7.62mm (0.3″) row spacing. Pin hole diameter should be 1.0 mm ±0.05 mm. Maintain at least 5 mm clearance above the slider’s travel path so the actuator can move through all three positions without interference from adjacent components or enclosure walls. The vertical orientation means the slider protrudes above the board; account for this height in your mechanical design.

Wave Soldering

Pre‑heat the PCB to 100–120°C for 60 seconds. Solder pot temperature: 250–260°C, contact time: 3–5 seconds per side. Keep the actuator upright during soldering; do not submerge the slider in the solder wave. Allow gradual cooling at 4–6°C per second.

Manual Soldering

Use a temperature‑controlled iron at 350°C with a 1.6 mm chisel tip. Solder each terminal for a maximum of 3 seconds. Start with the two common pins to align the part, then solder the remaining six position pins. After soldering, cycle the switch through all three positions to verify smooth operation.

Slide switches come in two primary actuation orientations: horizontal and vertical. A vertical slide switch DIP 8 pin like the SS-23L10 moves its slider perpendicular to the PCB surface, making it ideal when the board is mounted flat against a front panel and the switch needs to protrude through a slot. This is common in test equipment, audio gear, and industrial controllers where the user pushes or pulls the slider directly. Horizontal slide switches, in contrast, move parallel to the board, which suits edge‑mounted configurations but can be harder to integrate into a front panel. The vertical design also often provides a taller actuator that is easier to grip and gives clearer visual indication of the selected position. For panel‑mounted applications where the board sits behind a control surface, the vertical slide switch offers a straightforward, cost‑effective solution without the need for additional linkages or external actuators.

The SS-23L10 has been validated through a series of mechanical and environmental tests to guarantee 10,000 cycles of reliable operation. Key results include:

• Mechanical endurance: 10,000 complete slide cycles (position 1 to 3 and back). Contact resistance remained below 50 mΩ, and detent force stayed within ±20% of initial.
• Vibration test: 10–500 Hz, 1.5 mm double amplitude, 2 hours per axis per IEC 60068‑2‑6. No momentary contact opening longer than 10 µs.
• Thermal shock: 50 cycles between −30°C and +80°C per IEC 60068‑2‑14. No housing cracks or actuator binding, and contact resistance drift was less than 10 mΩ.
• Humidity aging: 96 hours at 40°C, 90–95% RH. Insulation resistance dropped by less than one decade, and no corrosion was observed on gold‑plated surfaces.

For a complete test report, contact engineering@vistarelectronics.com.

All SS-23L10 vertical slide switch units are shipped in anti‑static PVC tubes (30 pieces per tube), compatible with automatic insertion equipment. The switch is fully lead‑free and wave‑solderable with SAC305 alloy. Custom actuator colors, gold thickness (up to 0.76 µm), and alternative detent patterns are available upon request. Standard MOQ is 1,000 pieces. To request a free sample or volume quotation, contact sales@vistarelectronics.com with your company details and project application.